All three-position sliders on a spring, i.e. they return by themselves to the neutral position when the power supply is cut. 

Slider principle:

Position 1 neutral (power supply cut off) cylinder piston rod stalls - oil goes to overflow.

Position 2 operational (power supply to solenoid one only) cylinder piston rod extends.

Position 3 operating (power supply to solenoid two only) cylinder piston rod retracts.

Internal threads in the body:

Connection port supply: 1/2''

Connection port return: 1/2''

Connection port sections : 3/8''

Pressure range:

Maximum supply pressure: 250 Bar (3625.94 psi)

Maximum pressure on return: 50 Bar (725.19 psi)

Maximum pressure on sections: 300 Bar (4351.13 psi)

The opening pressure of the bypass valve increases proportionally with increasing flow rate:

180 bar (2610.68 psi) at 10 l/min

190 bar (2755.72 psi) at 20 l/min

200 bar (2900.75 psi) at 30 l/min

210 bar (3045.79 psi) at 40 l/min

It is recommended to check and set the correct pressure before commissioning.

Self-adjustable, full rotation 30 Bar (435.11 psi change).

Temperature range and oil type: 

Permissible ambient temperature: -40°C to +60°C

Permissible oil temperature: -15°C to +80°C

Recommended hydraulic oil on mineral oil basis, e.g. HL 32 or HL 46

Recommended oil filtration of 10 - 15 µ

Open centre system (pump-to-tank flow)

Modification / Spools with 1 to 7

HIGH QUALITY Made in EU

The hydraulic valve is widely used in hydraulic systems in construction, industry and agriculture.

The valve is adapted to various types of machines such as: 

sprayers, turners, cyclops, HDS loaders, construction machines, trailers, loaders, excavators, sweepers, agricultural machines, tractors, industrial machines and other hydraulically operated equipment.

Can be used with MF, CASE, Caterpillar, Komatsu, Volvo, JCB, Liebherr, Hyundai, Bobcat, Kawasaki, John Deere..... and many more.

Joystick 4 positions can operate with 2 section double acting valve or 4 section one way walve.

Material: 4 Position Joystick Controller is made of Exquisite workmanship plastic and metal, stable construction for long-lasting performance for joystick 2 way speed control.

Wide scope of application: 

The Joystick Switch is widely used in the industrial control circuit of AC 5 HZ, rated operation voltage ~38V and DC voltage of ~22V. for joystick switch latching for joystick 4 way dc.

Applicable scene:

A controller switch for magnetic starter, contactor, relay and other electrical wiring circuit  for 12v dc remote switch for  electric joy stick.

Type: 4 position self lock Contact: 4NO

Voltage: AC 38V 15A

Environment temperature: -25°C to +55°C (without zing)

Operating humidity: 45 ~ 85% RH (no condensation)

Contact resnce: ≤ 5mΩ Insulation resnce: ≥1Ω

The maximum pressure: 3 V, AC 5

Hz resnce Vibration: 5 Hz, amplitude of about 1mm) 

It has a rubber dust-proof, waterproof and oil-resistant sealing cover and rubber gaskets.

Assembly takes place by unscrewing the ring with the cover and the retaining ring, putting the joystick through the hole, fitting the seals and screwing the rings back on.

The Powerbeyond sleeve is a device that allows an additional manifold to be connected by using a pressure transfer port.

This solution provides power to another valve from a normally closed port allowing high pressure to be transmitted.

To use this function, it is necessary to remove the plug from the pressure transfer port and screw the pressure transfer sleeve in place.